223 GBC ABYSS SP-I II Hunter Straight Pull

Buy 223 GBC ABYSS SP-I II Hunter Straight Pull in NZ.
223BA-257

In stock?

Christchurch
Request
Auckland
Request
Wellington
Request
Hamilton
Request
Dunedin
Request
Napier
Request
Sockburn
Request
Motueka
Request
North Shore
Request
Richmond
Request
Supplier
Request

Seen it cheaper elsewhere?

Request a Price Match - Click here.

Share this with your friends!

  

Designed, Engineered, and Manufactured in New Zealand! Can be purchased on A-category firearms licence. 

GBC ABYSS SP-i (Straight Pull-ignition) Series II HUNTER Rifle, caliber .556/.223 Rem with 10 round magazine.

The GBC ABYSS SP-i Series II HUNTER Rifle is a completely new rifle from the ground up, it incorporates a new designed Upper & Lower Receiver, Bolt Carrier, Bolt, Bolt Catch, Ambidextrous Extended Magazine Catch, Barrel, Pull Handle with Knob and a Drop in Adjustable Trigger, all of which have been designed specifically for the GBC ABYSS SP-i rifle.

The GBC ABYSS SP-i Series II HUNTER Single Shot Rifle is a straight pull operated bolt, that's spring loaded, whereas, the bolt when it's fully charged backwards, then released, the forward returned motion of the bolt picks up a round chambering it, ready for ignition.

GBC ABYSS SP-i Series II HUNTER Rifle straight pull charging handle is reversible, meaning the charging handle can be fitted to the right or left hand side of the upper receiver, the rifle is also fitted with ambidextrous safety and ambidextrous extended magazine catch!

The GBC ABYSS SP-i Series II HUNTER Model Rifle as standard equipment, comes fitted with a Octagonal Carbon Fiber Free Float 12" Handguard, , Fab Defense Butt-Stock and a Drop in Adjustable Trigger.

All GBC ABYSS SP-i Series II Rifles are finished with a hard anodized coating on the aluminium parts then painted titanium grey using high tech Gun Kote, giving the rifle the look and feel it deserves.

All GBC ABYSS SP-i Series II Rifles have been designed to fit and use Magpul PMAG 10 round magazines. (Steel magazines should not be used).

Bolt Carrier: Manufactured from 4140 steel, harden to 45rc, then black nitrided, these are unique to the ABYSS SP-i Series rifles being smaller in diameter and shorter in overall length than any AR/M4 bolt carrier, they have no expansion chamber cut-out incorporated into the carrier, which stops anything other than single shot firing. The cam slot on the carrier has been re-designed and re-engineered, it's silky smooth with the locking and un-locking of the male bolt lugs from inside the female barrel extension lugs.

Charging Handle: Designed, Engineered, and Manufactured completely in New Zealand. It's reversible on the carrier, so to accommodate Left or Right handed shooters. It's held into place within the slot cut into the carrier with two high tensile screws. The arm is bent at 40 degrees downward and is fitted with a Acetal grove shaped knob, 21mm in diameter.

Bolt: The bolt is unique to the ABYSS SP-i Series rifles, for a start it doesn't have gas rings, the shaft that normally carry's the boss for the gas rings has been milled down, removing the gas ring boss completely leaving the shaft at a desired diameter to now act as the bush inside the carrier aligning the bolt dead center within the carrier itself so the bolt male lugs fit perfectly in the female barrel extension lugs.

Bolt Recoil System: This Item is all new to the Series II ABYSS SP-i Rifle. This now comes as a single one piece design, which includes the Rod Shaft, Spring, End Cap & Buffer Cushion all held together, makes stripping the rifle so much easier.

Bolt Catch: The bolt carrier is shorter in overall length and smaller in diameter along with the bolt carrier having a shorter stroke. The ABYSS SP-i Series II Bolt Catch has been milled with easy accessible touch pads cut into the design making it easy and faster to release the bolt. 

Barrel: Featuring a European Manufactured Cold Hammer Forged Steel Rifle Barrels with a 1:9 twist, the muzzle end is also threaded with a 1/2-28 thread for a muzzle brake or suppressor. The standard barrel length is 16 inches which has a Light to Medium contour for the ABYSS SP-i Series II HUNTER Model Rifle. 

Single Stage Drop In Adjustable Trigger: Designed with an adjustable trigger weight screw, something not all drop in triggers have. The drop in trigger has a clean, crisp, no creep hammer drop that has an adjustable trigger pull weight from 3lb to 5.5lb.

Specifications:
Caliber: 223 Rem
Magazine Capacity: 10
Magazine Type: Detachable
Action Type: Straight Pull
Barrel Length: 16"
Overall Length: 795mm-875mm
Barrel Thread: 1/2x28
Barrel Twist Rate: 1:9
Barrel Contour: Medium Light Tapered
Weight: 6lb-7oz
Width: 50mm at Magwell
Height: 185mm
Firearm Finish: Hard Anodised & Gun Kote
Barrel Finish: Blued
Receiver Finish: Hard Anodised & Gun Kote
Lower Material: 7075-T6 aluminum
Stock Brand: Fab Defense
Trigger Type: GBC Adjustable Drop-in
Safety Type: Ambidextrous
Colour: Titanium Grey
Grip Type: A2 Style
Country of Manufacturer: New Zealand


Purchase of this item requires a firearms licence, you will need to complete a Police Order Form and take it into your local police station to have it signed off. The form can be found from the link below.
Police Order Form

Gun City is NZ's largest firearms dealers. We have been selling, importing, exporting, manufacturing, customising and repairing firearms and accessories since 1978. We have the largest range of guns, ammo and accessories available now, online in New Zealand.

Please call our shop for more information on +64 3 379-8888 in Christchurch, New Zealand.

(223BA-257)